CALL FOR A FREE QUOTE (404) 999-4169
Small Hole Drywall Repair |
Big Hole Drywall Repair |
Accidentally put a small hole in your drywall? Even just patching a small hole requires drywall putty, a drywall nice, and sanding block. This seemingly simple task if not done properly will highlight imperfections in the wall and also create a large amount of dust from sanding. Our team can repair small drywall holes same day at a cost that makes it a no brainer for you to hire our team.
|
When there are larger holes in drywall, proper drywall repair is needed to fill the hole and make the wall look good again. While this can be a DIY job, it is not easy to ensure the repair looks good. Read the drywall repair how-to below to determine if the repair might be a DIY job or if hiring a pro would be a good option.
|
Tools and Materials Needed
A number of tools and materials are needed to repair larger holes. Before starting, have on hand a pencil, drywall saw, scrap lumber, tape measure, a piece of drywall, drywall screws, a drill, self-adhesive mesh joint tape, and a utility knife. Also, make sure to have the drywall joint compound, a drywall knife, a sanding sponge, and the primer and paint needed to match the surrounding wall.
Create an Opening with Straight Lines
The first important step for how to repair a drywall hole is to make sure the edges are straight. It’s much easier to cut drywall to fit when it has straight edges. Use the pencil to mark straight lines on the drywall, then use the drywall saw to cut along the lines. Always check for wiring or plumbing before cutting to avoid damage.
Secure Wood Backing Strips
Backing strips are needed on both sides of the opening and in the middle to help screw the new drywall piece into place. Use a few pieces of scrap wood longer than the opening to do this. Place them behind the drywall, then screw them into the existing drywall. Make sure the screws are at least an inch from the edge.
Install the New Piece of Drywall
Cut a new piece of drywall to match the opening. Use drywall that is the same thickness as the existing drywall, which is typically ½ inch. There shouldn’t be more than 1/8th of an inch space between the existing drywall and the new patch. Screw the new piece to the backing strips, keeping the screws at least one inch from the edges. Space the screws about six inches apart.
Add Tape to the Seams
Place the self-adhesive joint tape over all of the joints, making sure to overlap at the corners. Cut the tape to the length needed and make sure it is completely flat. There shouldn’t be any wrinkles in the tape, as this will show up once the wall is finished.
Add Drywall Mud to Seams
The seams will need to be covered with drywall mud. Start with a thin layer and spread over the mesh using the drywall knife. For the first layer, it should be possible to see the mesh a little bit. Once the mud is dry, add a second and third layer. Feather the edges for each layer so they taper to match the existing drywall.
Create a Smooth Surface
The mud will need to be sanded to ensure it is completely flat and tapers properly. The mud should not be sanded to the point the mesh can be seen again. Clean off all of the dust created with a dry rag, then add any drywall textures that are needed to ensure the patch matches the rest of the drywall. Allow the texture to dry completely.
Prime and Paint to Match
Once everything is sanded and dried, it can be primed and painted to match the remainder of the room. Always use a primer first to ensure the paint will adhere to the drywall. Let it dry, then add at least two coats of paint to the patch in the same color as the rest of the wall.
Should You Hire a Pro?
When there’s a large hole in drywall, it may be better to look into drywall repair near me instead of tackling it as a DIY project. While the steps themselves aren’t difficult, it is hard to ensure the patch can’t be seen once everything is textured and painted. Pros have the experience needed, and the drywall repair cost might not be as much as expected.
If you have a larger hole in the drywall that needs to be repaired, hiring a pro offers the best results. Work with a drywall repair contractor so the patch isn’t noticeable after it’s done. Give us a call today for a quote or to schedule a repair.
If you have a larger hole in the drywall that needs to be repaired, hiring a pro offers the best results. Work with a drywall repair contractor so the patch isn’t noticeable after it’s done. Give us a call today for a quote or to schedule a repair.
Atlanta Drywall Experts repaired my wall and it looks brand new! I am never attempting drywall hole repair again.
|
|
|
Serving the Greater Metro Atlanta Area
Looking for Drywall Repair Near me?
|